West Virginia Certificate MAIN
Add Header
Cody Success
Thursday, February 6, 2025
Add Header
Exam Information
- The Test consists of 40 questions worth 2.5 points each.
- A Passing Score is 80% or greater.
- You can take the certification exam at most two times in a year.
- You will learn the results after you submit the exam.
- If you pass the exam and earn the certification, we will contact with you via your email address so be sure you enter your email correctly.
- In case of any problems, please contact ccriscola@playgvg.com
Address
1291 Weil Street
Billings, MT, 59102
Phone Number
4062817600
00000001
Email
clindabury@playgvg.com
Operator/Retailer Name
000000001
Electronic Signature
Cody Success
1.) The Printer may be ‘hot-swapped’
b. Never
2.) The touch screens require calibration
d. a. and c.
3.) The Bill Acceptor must be calibrated
c. The JCM-UBA 24 is self-Calibrating
4.) The DC Power Supply
requires calibration
d. The DC supply does
not require calibrat
ion
5.) To replace the DC Power Supply the following tools are needed
d. None of the above
6.) The Grand Vision Gaming Terminal uses the
d. JCM UBA-24 bill acceptor and JCM UBA-14 bill acceptor
7.) The JCM UBA-24 belts may be cleaned with
a. Water (a damp cloth)
8.) The JCM UBA-24 optics may be cleaned with
b. Water (a damp cloth)
9.) The primary function of the ASD is to
c. Replace the carbon copy used with dot-matrix printers
10.) If an ASD becomes
faulty, it must
c. Stored as per stat
e regulations and rep
laced
11.) When loading the thermal printer paper
b. The printer paper must be loaded in the correct orientation to work properly
12.) If the lower monitor fails, the upper monitor can be installed as the lower monitor.
b. The upper and lower monitors are configured differently and cannot be simply exchanged
13.) The attendant reset switch may be used to
d. None of the above
14.) With regards to the JCM UBA-24 firmware used in the GVG Terminal
b. The GVG Terminal requires specific ID0G8 software
15.) The Logic Cube fan
draws air
b. Up out of
the Logic Cub
e
16.) The two case/cabinet fans draw air
a. Out of the cabinet
17.) The fan on the DC power supply
a. Draws air into the power supply
18.) The bill acceptor logs displayed at the top are
b. Newest bills in
19.) On the backplane, the button panel lamps are plugged into
d. J33
20.) The serial port used for SAS communication with the system is
a. J50
21.) The USB port assig
ned to the bill accepto
r is
a. J
24
22.) The lower and upper monitors use the following interface
c. Upper: VGA, lower: DVI
23.) The printer runs from the following supply
b. 24vdc
24.) The following tools are needed to remove the printer
a. No tools are needed
25.) A blinking blue bezel on the printer may mean the following
e. All of the above
26.) Un-switched power
connectors on the AC di
stribution box have pow
er that is
b. On regardless of th
e position of the powe
r switch
27.) The JCM UBA-24 bill acceptor is powered by
b. 12vdc
28.) The MUC (Multi Use Connecter) is located
c. On the main CPU board
29.) If no USB devices are operational (touch screens, ASD, bill acceptor and printer)
d. All of the above
30.) The Security ROM on the DPX-S425 is located
b. On the main CPU board in front of the MUC
31.) When installing th
e Security ROM in the S
425 Logic Cube, the DOT
on the ROM must be ori
ented
c. To the fr
ont of the c
ube
32.) The ¼ turn thumb latches on the top of the cube can be latched OPEN by
b. Pulling up and turning ¼ turn counter-clockwise
33.) Before removing the cube,
e. All of the above
34.) The monitors run on
c. 110vac
35.) All cabinet lighting other than the service lamp operate on
b. 12vdc
36.) The button panel p
ushbuttons and lamps ma
y be tested using
b. The Input Output Te
st panel in the audit
screens
37.) Once the VGMID number has been incorrectly set and ‘Save Changes’ pressed
c. The VGMID can only be cleared by using a new ASD and initiating a Ram Clear
38.) When servicing the service lamp cabling, or switch you must first
b. Un-plug the service cord from the side of the AC distribution box
39.) The monitor touch screens are powered using
a. 5vdc power from the USB cord
40.) To remove the DC p
ower supply unit on a G
VDD21S (Atlas),
c. Both the upper and
the lower monitors nee
d to be tilted
Grade
97.50
Add Header
Add Header
Add Header
Add Header
Add Header
Add Header
Add Header
Add Header
Add Header
Add Header
West Virginia Video Lottery Technician Certification Exam
About this template
Related templates
Award Certificate Template
This Award Certificate PDF Template contains the name of the awardee, signature and the date. You can insert 2 images using the PDF editor. This will surely make the award memorable to the employee or to the student.
Employee of the Month Certificate Template
An employee of the month certificate template is a type of document that employers use to generate certificates for team members who have gone above and beyond in a particular month.
Experience Certificate Template
Help an employee and prove the legitimacy of his or her work experience in the company by using this Experience Certificate Template. This document will be helpful when he or she applies to another company.
Adoption Certificate Template
If you are an Adoption agency, you might want to consider saving a ready-made Adoption Certificate Template to give to your clients. Jotform’s Free Adoption Certificate Template is very easy to use and modify.
Salary Certificate
Help your employees in their loan application or any situation that needs employment verification or income statement by using this Salary Certificate. This PDF template contains all required data that shows the employee has a job and has a regular income.